| |
| Technical
Specification |
 |
|
|
| ES150KG
|
* Lifting load 150kg
* Lifting speed 18.5m/min
* Wire rope diameter 5mm
* Wire rope length 26m
* Maximum working height 25m
* Electric motor power 0.45kW
* Motor speed 1320rpm
* Weight 39kg
* Niose level <75dB(A)
* Running current 5A
* Dimensions 770/520/330mm
* Packaging 820/500/350mm |
| ET200 |
* Lifting load 200kg
* Lifting speed 19m/min
* Wire rope diameter 5mm
* Wire rope length 26m
* Maximum working height 25m
* Electric motor power 0.7kW
* Motor speed 1320rpm
* Weight 42kg
* Niose level <75dB(A)
* Running current 7A
* Dimensions 770/520/330mm
* Packaging 820/500/350mm |
| Gantry Hoists |
Gantry Hoists BM-B-BS from IMER International
* Designed and built to the utmost reliability and with safety
in mind.
The gantry is available for 300 and 500 kgs carrying capacity
hoists and is provided with base bars, whilst front foot protection
and ballast boxes are also available as optional extras.
* The BM 300 hoist is supplied with a 3 push button pendant
and can also be supplied with a low voltage remote control.
The threephase hoists (B 300 and BS 500) are supplied with a
3 push button pendant and can also be supplied with a low voltage
remote control.
* The hoists frames are provided with a positioning brake to
hold the hoist in a fixed position while lifting. The safety
of operation is assured by the upper limit switch standard on
all models, additionally the 25 mt pendant hoists are provided
with a lower limit switch |
| AT30L |
| General: |
| Lifting Capacity |
:300Kg |
| Platform Dimensions |
:155x130cm |
| Free Standing mast |
:9 Meter |
| Max.mast height |
:40meter |
| Anchoring distance |
:6meter |
| Cable guide distance |
:4.5meter |
| Hoisting speed |
:13meter/minute |
| Power requirement |
:220v (single phases) 50
Hz |
| Motor Capacity |
:1,5kW |
| cable |
:3x2.5mm2 |
| Weight basic machine |
:ca.550Kg |
| Weight mast element |
:ca.45Kg |
| transport dimensions |
100x179x183cm(lxwxh) |
|
| Standard
Configuration: |
| * 1.5 meter
mast fitted to the base machine |
| * Mast-side
fence of 1,8 meters height and one side fence of
1,1 meters height |
| * Standard
lower, upper and emergency stops |
| * Proximity
switch for rack-end detection for safe erection
/ dismantling |
| * If, for whatever
reason the platform meets a obstruction while descending,
a limit switch will cut-off the command system |
| * Personel
safety through an automatic 2 meter stop above groung
level |
| *Motor protection
through a thermic switch |
| * Overspeed
brake |
| * One cable
guide directly above the cable drum |
| * Cable drum |
| * 4 Detachable
stabilizing beams |
| * Service switch
UP/STOP/DOWN/FLOOR-STOP attached to a 5 meter cable
with scaffolding coupling |
|
| extra's,
exchangable with type AT30HL/AT40/AT40H |
| * Mast sections |
| * Cable gudes |
| * Anchoring wall tiles |
| * Floor barrier without descent-and
stop-button, 5 meter cable |
| * Floor barrier without descent-and
stop-button, 10 meter cable |
| * Floor barrier without descent-and
stop-button, 5 meter cable (loop) |
| * Floor barrier without descent-and
stop-button, 10meter cable (loop) |
| * Platform stop bracket for precise
positioning at the various floors |
| * ILB-controlbox with computed
floor steps (max. 29 floors) |
| * Pivoting fence with limited
switch |
| * Loading ramp 0.6 meter with
limit switch |
| * Loading ramp 1.1 meter with
limit switch |
| * Remote control for easy erection
/ dismantling |
| * Auxilary jib for mast erection
/ dismantling |
| * 2 wheels with drawbar and twocoupling |
| * Lifting-eye for shifting the
hoist with a crane |
| Product specification
may vary from these specifications |
|
| AT50 |
General: |
| |
| lifting capacity |
: 500Kg |
| Platform Dimensions |
150x150cm 250x150cm(optional)
300x150cm(optional) |
| Free standing mast |
: 10.5 meters |
| Max. mast height |
: 75 meters |
| Anchoring distance |
: 6 meters |
| Cable guide distance |
:4.5 meters |
| hoisting Speed |
: 24meters/minute |
| Power requirement |
: 380v-3 phase-50 Hz |
| Motor capacity |
: 4.0kW |
| Cable |
: 4x4mm2 |
| Weight basic machine |
: c.a900 Kg |
| Weight mast sections |
: c.a 60 Kg |
| Transport dimension |
: 280x166x173cm (lxwxh-without
wheels) |
| Transport dimension |
: 365x199x189cm (lxwxh-with wheels) |
| Standard
Configuration: |
| * 1.5 meter mast
fitted to the base frame |
| * Mast-side platform
fence of 1,8 meter height and one side fence 1,1 meter
heigh |
| * Standard lower,
upper and emergency stops |
| * Proximity switch
to detect end of the rack for safe erection/dismantling |
| * Mast-end safety
section |
| * If so for whatever
reason the platform meets a obstacle while descending,
a limit switch will cut-off the command immediately |
| * Personel safety
by a 2 meter-stop above groundlevel while lowering the
platform |
| * Phase reversable
switch with motor rotation protection |
| * Overspeed brake |
| * One cable guide
directly above the cabledrum |
| * Cable drum |
| * Service switch
UP/STOP/DOWN/FLOOR-STOP attatched to a 5 meter cable with
scaffold coupling. |
| Extra's,
exchangable with type AT75 |
| * mast sections |
| * cable guides |
| * Anchors/wall
ties |
| * Floor barrier
without descent-and-stop-button, 5 meter cable |
| * Floor barrier
without descent-and-stop-button, 10meter cable |
| * Floor barrier
without descent-and-stop-button, 5 meter cable(loop) |
| * Floor barrier
without descent-and-stop-button, 10 meter cable(loop) |
| * Platform stop
bracket for precise positioning at the various floors |
| * ILB-controlbox
with computed floorstops(max. 29 floors) |
| * Pivoting fence
with limit switch |
| * Loading ramp
with 0.6 meter with limit switch |
| * Loading ramp
with 1.1 meter with limit switch |
| * Side extension
set for platform 250x150cm (400kg lifting capacity) |
| * Side extension
set for platform 300x150cm (350kg lifting capacity) |
| * Remote control
for easy erection / dismantling |
| * Auxilary jib
for mast erection / dismantling |
| * Lifting-eye
for shifting, loading and unloading with a crane |
| * 4-wheels of
which the front-ones can be steered with a drawbar |
| * 4 haevy duty
screwspindles for stabilising and leveling the hoist |
| Product specification
may vary from these specifications |
|
| AT75 |
| General: |
| Lifting capacity |
750 Kg |
| Platform Dimensions |
150x150cm 250x150cm (optional)
300x150cm(optional) |
| Free standing mast |
7.5 meters |
| max.mast height |
75 meters |
| Anchoring distance |
6 meters |
| Cable guide distance |
4.5 meters |
| Hoisting speed |
21 meters/minute |
| Power requirement |
380 V ( 3 phases ) 50 Hz |
| Motor Capacity |
5.5 kW |
| Trailing cable |
4x4mm2 |
| Weight basic machine |
ca.900Kg |
| weight mast section |
ca.60Kg |
| Transport dimensions |
280x166x173cm (lxwxh - without
wheels) |
| Transport dimensions |
365x199x189cm (lxwxh - with wheels) |
| Standard
configuration: |
| * 1.5 meter mast
fitted to the base frame |
| * Mast-side platform
fence of 1,8 meter height and one side fence 1,1 meter
height |
| * Standard
lower-,upper- and emergency stops |
| * Proximity switch
to detect end of the rack for safe erection/dismantling |
| * Mast-end safety
section |
| * If, forwhatever
reason the platform meets a obstruction while descending,
a limit switch will cut-off the command immediately |
| * Personel safety
by a 2 meter stop above ground level while lowering the
platform |
| * Phase reversable
switch with motor rotation protection |
| * Overspeed emergency
brake |
| * One cable guide
directly above the cable drum |
| * Cable drum
|
| *
Service switch UP/STOP/DOWN/FLOOR-STOP attatched to a
5 meter cable with scaffold coupling |
| Extra's,exchangeable
with type AT50 |
| * mast sections |
| * Cable guides |
| * Anchors / wall
ties |
| * Floor barrier
without descent-and stop-button, 5 meter cable |
| * Floor barrier
without descent-and stop-button, 10 meter cable |
| * Floor barrier
without descent-and stop-button, 5 meter cable (loop) |
| *
Floor barrier without descent-and stop-button, 10 meter
cable(loop) |
| *
Platform stop bracket for precise positioning at the various
floors |
| * ILB- controlbox
with computed floorstops (max.29 floors) |
| * Pivoting fence
with limit switch |
| * Loading ramp
0.6 meter with limit switch |
| * Loading ramp
1.1 meter with limit switch |
| * Side extension
set for platform 250x150cm (650 Kg lifting capacity) |
| * Side extension
set for platform 300x150cm (600 Kg lifting capacity) |
| * Remote control
access for easy erection/dismantling |
| * Auxilary jib
for mast erection/dismantling |
| * Lifting eye
for shifting, loading and unloading with a crane |
| * 4-wheels of
which the front-ones can be steered with a drawbar |
| * 4 heavy duty
screwspindles for stabilising and levelling the hoist |
| Product specification
may vary from these specification |
|
| AT1000 |
| Description/type |
|
| Lifting capacity |
1000Kg |
| Platform dimensions |
1,5x2,2m 1,5x3,2m
1,5x4,2m |
| Anchoring distance |
12m |
| Lifting speed 2 motors |
24 m/min |
| Power requirement |
400V |
| Motor capacity 2 motors |
2x5.5kw |
| Trailing cable |
5x10mm2 |
|
| AT2000 |
| Description/type |
|
| Lifting capacity |
1500Kg |
| Platform dimensions |
1,5x2,2m 1,5x3,2m
1,5x4,2m |
| Anchoring distance |
12m |
| Lifting speed 2 motors |
24 m/min |
| Power requirement |
400V |
| Motor capacity 2 motors |
2x7.5kw |
| Trailing cable |
5x10mm2 |
|
| MP50 |
| General: |
|
| Capacity |
: 500kg. incl. 3 persons. |
| platform dimensions |
: 150x150cm |
| Max. mast height |
: 75m |
| Anchoring distance |
: 6m |
| cable guide distance |
: 4,5m |
| Platform speed |
: 0,2m/sec |
| Voltage |
: 420V (3 phase) |
| Motor capacity |
: 3 KW |
| Power lead cable |
: 4x2,52 |
| weight basic machine |
: approx. 900 kg |
| Weight mast section |
: appprox. 60 kg |
| transport dimension |
: 245x190x225cm. (lxwxh) |
| Standard
equipped with: |
| * 1,5 m base
mast |
| * 1,8m vertically
sliding platform fence (mast slide) and a 1,1m high fixed
one opposite |
| * Loading ramp
1,1m and one of 0.6m high facing the building. Both ramp
are electro/mechanically locked. |
| * Bottom/top
and top emergency limit switches |
| * Proximity switch
for rack detection to give extra security during erection/dismantling
of the hoist. |
| * Platform stop
2m above ground level with accoustic signal while descending
further. |
| * Phase protection |
| * Phase reversal
switch |
| * Overspeed centrifugal
safety brake |
| * 1 cable guide
positioned directly above the cable drum |
| * Control panel
UP/STOP/DOWN/STOP/NEXT FLOOR and a button to activate
a horn to alert people. |
| *
Hoist mode control pendant |
| Extra's |
| * Mast extensions
1,5m length+ |
| * Cable guides+ |
*
Mast anchoring set+ |
| * Floor stop
bracket for in the mast |
| * Sliding landing
gate without down/stop buttons |
| * Pendant with
down/stop buttons per landing |
| * Auxilary jib
for easy erection and dismantling+ |
| * Lifting eye
to lift the transport platform with a crane.+ |
| * 4 heavy duty
screew spindles for easy levelling.+ |
| * 4 pneumatic
tyres with steering towbar |
| * Base enclosure
fence with electromechanical locking. |
| * Roof structure
of mesh metal for more safety |
| * Automatic greasing
system |
| * Overload sensoring
device |
| * Remote control
pendant for drop-test and reset |
| '+', also exchangable
with our standard AT50/AT75 material hoists. |
| Product specification
may vary from these. |
|
AT60P
|
| Technical
specifications: |
| Pay load |
600kg or 8 persons |
| Max. mast height, free standing |
7,5 mtr |
| Max. mast height, anchored |
100 mtr |
| Wall-tiles intervals |
every 9 mtr |
| Cable guide intervals |
every 4,5 mtr |
| Cabin dimensions exernal |
167x163x230cm |
| Cabin dimensions internal |
153x132x210cm |
| Cabin dimensions door access |
125x200cm |
| Ground cage dimensions external |
213x285x250cm |
| Transport dimensions |
285x213x285cm (inc.lifting yoke
297 cm) |
| Weight base unit |
1900kg |
| Drive |
rack-and-pinion |
| Motor |
5,5kW - 380 volt - 50 Hz |
| Current connection |
35 Amp |
| Starting current |
60 Amp |
| Nominal current |
12 Amp |
| lift control |
semi-automatic in liftcabin by
2 push-buttons UP-DOWN and OVERRIDE(constant pressure),
floorstop by guiders at mast. |
| Stabilizers |
1 stamp under base-mast and 4
screw spindles |
| Power cable |
4x4mm2 (0-50mtr)-4x6mm2(51-100mtr) |
| Controlling current |
42 Volt |
| Mastelement length |
147cm |
| Mastelement weight |
80kg |
| Module rack |
m=6 |
| Optional
Equipment: |
| * Landing doors
incl. electric end-switch |
| * Landing barriers
inc. electric end-switch |
| * Set wall-tie
clamps with coupling 1 1/2" |
| * groundcage
loading ramp |
| * Lifting yoke
for transport purposes (also topmastsection) |
| *
Davit with handwinch for mast erection |
Lift Series Ladder Hoists
from IMER International
* The lift ladder hoists are designed to transport material
of various types and dimensions within small space job-sites.
The wide range of accessories available make the lifts
suitable for the various job-site requirements, from refurbishment
to construction sites. Three models are available with
carrying capacities from 150 to 200 kg and lifting speed
from 25 to 36 m/min. |
BUMPA loading machine from MACE Industries
Ltd
* The time consuming, back breaking chore of loading repetitive
heavy loads roof high becomes quick and easy with a BUMPA
loading machine, carried on the roof of any small van,
erected up and running in under 6 minutes.
BUMPA's capacity to clear a pallet of concrete blocks
in under 1 minute or 1000 tiles in 25 minutes - from single
to 3 storey lift - makes it a must for every roofer and
builder. Today's regulations state you must provide a
mechanical means for handling repetitive heavy loads,
rather than relying on manual labour. Bumpa is proven
to double your performance for half the effort, helping
you to compete and comply! |
|
|
|
|
